Hose Supplier | Hose Manufacturing | Supply Hose and Fittings | Hose Distributor Malaysia

Cement Discharge Hose 10 Bar Overview

This cement discharge hose is designed for transferring dry cement, pebble lime and selected abrasive dry materials. The product title identifies a 10 bar pressure class, while the existing construction information lists an abrasion-resistant SBR tube and cover with multiple layers of high-tensile synthetic cord reinforcement.

Fastul R1AT Hydraulic Hose Overview

Fastul R1AT hydraulic hose is a single-wire-reinforced hose for selected hydraulic fluid-power applications. The existing product information identifies DIN EN 853 1SN, a synthetic-rubber tube, one layer of high-tensile steel-wire reinforcement and an abrasion- and ozone-resistant synthetic-rubber cover.

Fastul R8 Thermoplastic Hose Overview

Fastul R8 is a thermoplastic hydraulic hose for selected high-pressure fluid-power applications where a compact, lightweight hose construction may be required. The existing product information identifies SAE 100R8 / EN 855 R8, a nylon thermoplastic core, two braids of high-tensile synthetic fibre and an abrasion-resistant polyurethane cover.

Fastul 4SH Hydraulic Hose Overview

Fastul 4SH hydraulic hose is a four-wire-spiral hose for selected high-pressure hydraulic applications. The existing product information identifies DIN EN 856 4SH, a synthetic-rubber tube, four spiral layers of high-tensile steel wire and an abrasion- and ozone-resistant synthetic-rubber cover.

Fastul R2AT Hydraulic Hose Overview

Fastul R2AT hydraulic hose is a two-wire-reinforced hose for selected hydraulic fluid-power applications. The existing product information identifies DIN EN 853 2SN, a synthetic-rubber tube, two layers of high-tensile steel-wire reinforcement and an abrasion- and ozone-resistant synthetic-rubber cover.

KC Nipple Overview

A KC nipple is an industrial hose fitting used to connect compatible hose, piping or equipment interfaces. Advtech Engineering supplies KC nipple options for enquiries in Malaysia, subject to confirmation of hose size, end geometry, thread, material, pressure, media and the required retention method.

High Pressure Jack Hose Overview

High Pressure Jack Hose is listed for compact high-pressure hydraulic lines used with jack and lifting equipment. The published product information identifies a 700 bar application reference, a polyester elastomer inner tube and a black polyurethane cover.

Composite Hose Type-STS Overview

Composite Hose Type-STS is a product designation in Advtech Engineering’s composite hose range. Because the original product description does not publish the exact layer materials, wire construction, pressure, temperature or media compatibility, the type code alone should not be used to approve a hose for service.

Bulk Material Suction Hose 10 Bar Overview

Bulk Material Suction Hose 10 Bar is designed for suction and transfer duties involving dry materials such as cement, gravel, grain, animal feed and sand. The published construction combines an abrasion-resistant tube, textile reinforcement, helix wire support and an embedded antistatic copper wire.

Nitrogen Hose 20 Bar Overview

Nitrogen Hose 20 Bar is an extruded softwall rubber hose listed for transfer of nitrogen gas or natural gas. The published construction uses an NBR/SBR blend tube, yellow NBR/PVC/SBR blend cover and high-tensile synthetic yarn reinforcement.

LPG Hose 20 Bar Overview

LPG Hose 20 Bar is a product listing in Advtech Engineering’s gas hose category. The original description does not publish the exact tube, reinforcement, cover, temperature range, pressure table, standards or approved LPG composition.

XLPE Chemical Delivery Hose 16 Bar Overview

XLPE Chemical Delivery Hose 16 Bar is a softwall hose listed for delivery of a range of chemicals. Its published construction uses an XLPE tube, green EPDM blend cover, multiple layers of high-tensile synthetic cord and an embedded antistatic copper wire.

Oil Discharge Hose 10 Bar Overview

Oil Discharge Hose 10 Bar is a softwall rubber hose listed for transfer of oil and petroleum-based products. The existing product information refers to products with aromatic content up to 50% for fuel-connector service.

PVC Layflat Hose Overview

PVC Layflat Hose is a lightweight, flexible discharge hose commonly used for water delivery, pump discharge, irrigation and general site dewatering. It stores flat when not pressurised and is available in cut lengths or assemblies. Final selection must match the hose size, working pressure, temperature, fluid, fittings and routing conditions.

Silicone Ducting Hose is intended for selected hot-air, dry-fume, exhaust and ventilation applications that require a flexible high-temperature duct. The air or gas composition, temperature profile, airflow, vacuum, hose size and installation environment must be reviewed before selection.

Camlock Part DP Overview

Camlock Part DP is a dust plug used to close a compatible female camlock coupler when a hose or pipeline connection is not in use. It helps protect the open connection from dirt and debris. The exact size, material, mating series, gasket arrangement and pressure conditions must be confirmed before selection.

Camlock Part DC Overview

Camlock Part DC is a dust cap used to close a compatible male camlock adapter when a hose or pipeline connection is not in use. It helps protect the open adapter from dirt and debris. The exact size, material, mating series, gasket and pressure conditions must be confirmed before selection.

Water Suction Hose 20 Bar Overview

Water Suction Hose 20 Bar is a hardwall rubber hose listed for suction of water and non-corrosive fluids in agricultural, industrial and general transfer duties. Its helix-wire-supported construction helps the hose resist collapse under suction.

Camlock Part F Overview

Camlock Part F is commonly configured with a male camlock adapter end and a male threaded connection. It connects a compatible female camlock coupler to threaded equipment or pipework. The exact thread standard, size, material, media and pressure conditions must be confirmed before selection.

Camlock Part E Overview

Camlock Part E is commonly configured with a male camlock adapter end and a hose shank. It connects a compatible female camlock coupler to a flexible hose. The exact hose bore, shank profile, attachment method, material, media and pressure conditions must be confirmed before assembly.

Sandblasting Hose 10 Bar Overview

Sandblasting Hose 10 Bar is a softwall abrasion-resistant hose listed for delivery of sand and cast-steel shot. Selection must match the abrasive, hose size, pressure, temperature, couplings, static-control requirements and blasting equipment.

• Tube: antistatic black NR blend with high abrasion resistance.

Camlock Part D Overview

Camlock Part D is commonly configured with a female camlock coupler and a female threaded connection. It connects a compatible male camlock adapter to threaded equipment or pipework. Confirm the thread standard, camlock series, size, material, gasket, media and pressure before selection.

Water Discharge Hose 10 Bar Overview

Softwall rubber hose for transfer of water and non-corrosive liquids in construction, industry and agriculture. Confirm fluid, size, pressure, temperature, fittings and routing.

• Tube: black NR blend.
• Cover: black NR blend, abrasion- and weather-resistant.